- 您现在的位置：买卖IC网 > Sheet目录629 > P1641100 (Red Lion Controls)P16 ANALOG CONTROLLER
7.5 MODULE 9 F ACTORY S ERVICE O PERATIONS ( 9-FS )
9-FS CNFP
A
CodE
FACTORY
SERVICE CODE
PARAMETER MENU
????
??
CALIBRATION
RTD Resistance (T16)
RTD calibration requires a precision 277.0 ohm resistor with an accuracy of
0.1 ? (or better). Connect a jumper between terminals 9 and 10 with a 0 ohm
jumper between 9 and 8 at ???1 and the 277.0 ohm resistor between 9 and 8 at
???2 . If using thermocouple only, the RTD calibration need not be performed.
The controller is fully calibrated from the factory. Recalibration is
recommended every two years by qualified technicians using appropriate
equipment. Calibration may be performed by using the front panel or with the
TP16KIT. The front panel method is explained below. (Refer to the TP16KIT
bulletin for calibration instructions using TP16KIT cable and software.)
Calibration may be aborted by disconnecting power to the controller before
exiting Factory Service Module ??F? . In this case, the existing calibration
settings remain in effect.
Note: Allow the controller to warm up for 30 minutes minimum and follow
the manufacturer ’s warm-up recommendations for the calibration source or
measuring device.
PROMPT
??????
?????
?????
?????
????1?
????2?
APPLY
0.0 ohm
277.0 ohm
FRONT PANEL ACTION
Press J until ?? , press A .
Press A .
Press A .
Press B for ??? , press A .
After 5 seconds (minimum), press A .
After 5 seconds (minimum), press A .
Millivolt Calibration (T16)
Millivolt calibration requires a precision voltage source with an accuracy of
0.03% (or better) connected to terminals 8 (comm.) and 9 (+). When calibrating
the input, the millivolt calibration must be performed first, then the Cold Junction
or RTD Resistance.
Input Calibration (P16)
Process calibration requires a precision signal source with an accuracy of
0.03% (or better) that is capable of generating 10.0 V connected to terminals 8
(COMM) and 9 (+10V) and 20.00 mA connected to terminals 8 (COMM) and
10 (20mA). The current calibration can be skipped by pressing A at the not
applicable prompts if using the controller for process voltage only.
PROMPT APPLY FRONT PANEL ACTION
PROMPT
??????
?????
????1?
????2?
??????
??????
??????
APPLY
0.0 ohm
14.0 mV
28.0 mV
42.0 mV
56.0 mV
FRONT PANEL ACTION
Press J until ?? , press A .
Press B for ??? , press A .
After 5 seconds (minimum), press A .
After 5 seconds (minimum), press A .
After 5 seconds (minimum), press A .
After 5 seconds (minimum), press A .
After 5 seconds (minimum), press A .
??????
?????
????1?
????2?
??????
??????
??????
??????
0.0 ohm
2.5 V
5.0 V
7.5 V
10.0 V
0.0 mA
Press J until ?? , press A .
Press B for ??? , press A .
After 5 seconds (minimum), press A .
After 5 seconds (minimum), press A .
After 5 seconds (minimum), press A .
After 5 seconds (minimum), press A .
After 5 seconds (minimum), press A .
After 5 seconds (minimum), press A .
Cold Junction (T16)
Cold Junction calibration requires a thermocouple of known accuracy of
types T, E, J, K, C or N (connected to terminals 8 and 9) and a calibrated
external reference thermocouple probe measuring in °C with resolution to
tenths. The two probes should be brought in contact with each other or in some
way held at the same temperature. They should be shielded from air movement
and allowed sufficient time to equalize in temperature. (As an alternative, the
T16 thermocouple may be placed in a calibration bath of known temperature.)
If performing the millivolt calibration prior, verify that the correct input type is
configured in Input Module 1?I? before performing the following procedure.
(After the millivolt calibration the controller will default to type J.) If using RTD
only, the cold junction calibration need not be performed.
PROMPT
COMPARE
FRONT PANEL ACTION
Press J until
?? , press A .
??????
Press A .
?????
Press B for
??? , press A .
?????
Press B or J to adjust the
Top display to
bottom display until the top
external
process display matches the
reference
external reference then press A .
??????
20.0 mA
After 5 seconds (minimum), press A .
19
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
P1Z9ACR900W12
DIODE MOD PWR-BRIK DL 1200V 740A
PA3716
TOOL REPLACEMENT HEAD SET
PAXCDL10
ANALOG OUTPUT CARD
PAXLC800
COUNTER 8-DIGIT BI-DIR COUNT
PAXLPT00
METER PROCESS TIME 6-DIGIT
PAXLR000
METER RATE INDICATION 6-DIGIT
PB52233SLK
PROJ BOARD COLDFIRE M52
PD412411
DIODE MOD ISO DUAL 2400V 1100A
相关代理商/技术参数
P1641110
制造商:Red Lion Controls 功能描述:PROCESS CONTR, 1/16DIN DC ANALOG 2 ALRM 制造商:Red Lion Controls 功能描述:DC W/ANALOG OUT 2 ALARMS
P1-64121
制造商:OTTO 功能描述:Pushbutton Switches Style F Scrw LoLev Red Button 制造商:OTTO Engineering Inc 功能描述:Switch Push Button N.O. Round Button 10A 115VAC 28VDC Momentary Contact Screw Panel Mount
P1-64122
功能描述:按钮开关 Style F Scrw LoLev Black Button
RoHS:否 制造商:OTTO 触点形式: 开关功能: 电流额定值: 电压额定值 AC: 电压额定值 DC: 功率额定值: 安装风格: 照明: 照明颜色: IP 等级: 端接类型: 触点电镀: 执行器: 盖颜色: 封装: 可燃性等级:
P1-64122W
制造商:OTTO 功能描述:Pushbutton Switches Style F Scrw LoLev Black Button 制造商:OTTO Engineering Inc 功能描述:STYLE F,SCREW,LOW
P1-64128
功能描述:按钮开关 Style F Scrw LoLev Gray Button
RoHS:否 制造商:OTTO 触点形式: 开关功能: 电流额定值: 电压额定值 AC: 电压额定值 DC: 功率额定值: 安装风格: 照明: 照明颜色: IP 等级: 端接类型: 触点电镀: 执行器: 盖颜色: 封装: 可燃性等级:
P1-64129
功能描述:按钮开关 Style F Scrw LoLev White Button
RoHS:否 制造商:OTTO 触点形式: 开关功能: 电流额定值: 电压额定值 AC: 电压额定值 DC: 功率额定值: 安装风格: 照明: 照明颜色: IP 等级: 端接类型: 触点电镀: 执行器: 盖颜色: 封装: 可燃性等级:
P1-64131
制造商:OTTO Engineering Inc 功能描述:Switch Push Button N.O. Round Button 10A 115VAC 28VDC Screw Panel Mount
P1-64132
制造商:OTTO Engineering Inc 功能描述:Switch Push Button N.O. Round Button 10A 115VAC 28VDC Screw Panel Mount